Home > How To > Installing A Slave Harddrive?

Installing A Slave Harddrive?

Contents

Reply Ardiana December 31, 2016 at 3:27 pm IDE cables normally have 3 outlets, one for motherboard and two for hard drives/ CD drives. Reply Brad Jobs January 22, 2011 at 4:39 am That is pretty darn good step by step guide to install a second physical hard drive. Add > (load Disk 1 (disk 0 being old hdd and disk 1 being new hdd)) from which you're going to borrow space 5a. Obviously it depends on the individual system, but for the most part I'd say computers still running IDE drives are really too old to be in general use, other than for http://goinsource.com/how-to/installing-slave-drive.html

I'm starting to think my hardware knowledge is woefully out of date. Reply Ardiana December 31, 2016 at 3:27 pm IDE cables normally have 3 outlets, one for motherboard and two for hard drives/ CD drives. Install Windows on the new drive5. Once the IDE/EIDE cable has been connected to the computer hard drive, connect the power cable. http://www.makeuseof.com/tag/install-hard-drive/

How To Install A Second Hard Drive Windows 10

Start with a pc with 7 factory installed and slave the old hdd and run programs from it. ASSIGN THE FOLLOWING DRIVE LETTER > next 6. You’ve completed the hardware aspect, but not the software aspect! Others will have a note on the drive label instead: Figure Out Your Existing IDE Scheme It’s more than likely you currently have both a CD-ROM drive and hard disk plugged

Try to position the drives with some space in between each other to make room for air to flow and improve cooling. If yours is of the type at the top, with a wide ribbon cable – it’s a very old connection type called IDE. But in general, if your computer doesn't even have SATA (which was created 10 years ago, by the way), then it probably isnt much good to run win7... Second Hard Drive Not Showing Related Resources solved Upgrading to Windows 8.

If this is not possible (e.g. Reply James Bruce August 29, 2016 at 2:53 pm No, not if you're already using it - each port can support one device (unlike IDE which did two) Reply Dhrjinder August Did this article help you?

Re installing dozens of old apps that We have had for years and might not have discs for is a huge time sink.

GTECHS 12,206 views 8:43 How to recover data from a hard drive (stuck heads: buzzing, clicking, etc) - Duration: 10:28. How To Configure A Second Hard Drive All Rights Reserved. Great article. Poor thing even needs a 3.5" floppy drive to work.

How To Install A Second Hard Drive Windows 7

Thanks for voting! ASSIGN THE FOLLOWING DRIVE LETTER > next 6. How To Install A Second Hard Drive Windows 10 I'm starting to think my hardware knowledge is woefully out of date. How To Install A Second Sata Hard Drive select the partition (the box indicating old drive with drive letter, for example D, which needs extra space) 3a.

Most tower cases can have their sides removed with just two screws. Check This Out Most hard drive kits include a data cable (SATA or IDE, depending on the drive), a power adapter cable (with some SATA drives), and screws. Any later program installations (apart from system-related ones) will be done to the new disk – have a dedicated place/path for that. Most drives are supplied with the jumper set to cable select - this means that the position of the drive (master or secondary) is dependent on which connector you use. How To Connect Two Hard Disk In One Pc

Formatting could take an hour or more, depending on drive capacity. For example, if a CD-ROM is present on the same cable as a hard drive, it must be set to Slave. Reply Terrion September 10, 2016 at 12:36 pm Hello, I have a question. Source So, keep in mind to buy a device that is in align with max supported port speed to get the max performance.

Reply Ryan Burns June 23, 2016 at 6:40 am Laptops can have 2 hard drives just google "cd to hdd adapter" i'm using one now i have a ssd and a How To Install A Second Hard Drive In A Pc solved Installing Windows 8.1 on New PC Using Old HDD With Windows 7 solved installing old sata HDD with windows back into PC which has a new SSD with windows solved This jumper must cover the appropriate pins to set the drive as a Single, Dual Master, Dual Slave, or Cable Select.

Likewise, bus speed should be taken into consideration when buying a new RAM.

Most ribbon cables have 2 attachments - your main drive should be attached to the master attachment. The cable length will affect your choice too, as IDE cables are usually quite short. Have fun. How To Slave A Sata Hard Drive right-click > extend volume > next 4a.

Your new hard disk should be listed in the centre pane. All Rights Reserved. The intent is that, if there's a disaster in future, it will try to recover clean copies of OS files from the other drive and restore the main drive, so you have a peek here With modern SATA, which is a serial bus instead of the older parallel EIDE bus, things are simpler.

Type diskmgmt.msc and enter 3. Sign in to make your opinion count. So, in the case your new HDD has no active partition (windows is not installed in it – it is used as an internal flash drive for storage purpose), I personally The only thing to be aware of is that the power supply and cables are different. (as pictured in the article) They will only go in one way though as the

But if you're replacing your boot drive and you have an empty bay, follow our steps for adding a second drive. Sign in to report inappropriate content. So, to make it a slave device, I place a jumper over the central (second) pair. Ensure everything works6.

Create an account EXPLORE Community DashboardRandom ArticleAbout UsCategoriesRecent Changes HELP US Write an ArticleRequest a New ArticleAnswer a RequestMore Ideas... I have a second SATA III connection in my PC, but no secondary PSU cable to power my HDD. When you first turn on the computer, your new hard disk may not be ready for use immediately. Links to various computer and hardware manufacturers can be found on our Support Listing.

If your computer has an available 3.5-inch bay it is highly recommend that this drive bay be used to install the hard drive, as no additional brackets will be required. FORMAT THIS VOLUME WITH THE FOLLOWING SETTINGS NTFS DEFAULT (name it with whatever you want) PERFORM A QUICK FORMAT 7.