Home > Is This > Is This A Hardware Problem?

Is This A Hardware Problem?

If you just installed or upgraded hardware drivers and blue screens start, try uninstalling the drivers or using system restore -- there may be something wrong with the drivers. You can try scanning your computer for malware and running System Restore to restore your computer's system software back to its previous working state, but these aren't  guaranteed ways to fix This may help to eliminate the software angle* and flag up a hardware problem. *assuming everything works out of the box, which only happens around 70% of the time for me...

Then repeat steps 1 through 7 again. Source

If the new cartridge does not help the streaking, place the cartridge back inside the original packaging and save it until the other cartridge has been used up. Once in the Control Panel, look for the Display icon. If "Mute all" check box is checked, there will be no sound. If you still see the same problem - for example, if your computer is blue-screening and continues to blue-screen after reinstalling Windows -- you know you have a hardware problem and

Motherboard: Motherboard problems can be extremely tough to diagnose. Instead, security engineers take comfort in the complexity itself. If the printer still does not print, please contact the Help Desk x1112. Symptom The screen is too bright or too dark Diagnosis Check if the Brightness or contrast control is at the appropriate position, not at the maximum or minimum.

Be sure to use an Over Current Protector (Surge Protector) and to have an UPS( Uninterruptable Power Supply). If the audio is choppy or slow, it usually means that the processor is working at an elevated level, or there is not enough RAM to run all programs loading. Most of the time a small scratch won't matter. If you have a tower computer you should see indicator lights just above the power button on the PC, if you see any numbers lit up report this to the Help

Errors in the software or the operating system installed. As a last ditch effort, check the problem in safe mode. CD Troubleshooting Symptom The computer won't read the CD Diagnosis Check to see if the label side of the CD is faced up Check to see if the CD be read http://www.pau.edu.tr/bidb/en/sayfa/hardware-problems But they're wrong.

Especially, check the horizontal frequency. On the Power schemes tab, you should see where it says "Turn off monitor:" with an amount of time next to it. This process is known as "restarting." Flag as duplicate Thanks! Thanks for letting us know.

Music files, movies, digital pictures, and other big data files can fill up your hard drive. That means reinstalling Windows or using the Refresh or reset feature on Windows 8. If the power supply dies completely, your computer won't power on and nothing will happen when you press the power button. Did this article help you?

If you cannot see any lightson your keyboard when you press the Caps Lockor Num Lock key, it may be a dead keyboard. this contact form Place the mouse arrow on this icon. Computer CD/DVD disc drives How to test a computer CD-ROM or DVD drive for failures. If your computer runs fine first thing in the morning but crashes after several hours it could be heat related problems.

If the new toner cartridge does not improve the streaking problem, return old cartridge to the printer and place the new toner cartridge back in its original packaging for later use. The following are things which indicate the problem is likely to be hardware related:A problem begins to occur regularly even though no new software has been installed or the operating system It just beeps Read our Beep Codes List Check the Keyboard Check the Video Card Check the Memory Check the Motherboard When I turn it on... have a peek here When Hardware Starts to Fail… Here are some common components that can fail and the problems their failures may cause: Hard Drive: If your hard drive starts failing, files on your

running similar tasks, problems occurring at similar times, etc). In December of 1967 the Silver Bridge collapsed into the Ohio River, killing 46 people. Check to see if you can print a Windows test page The windows test page is a basic communication test between your computer and the printer.

If you can identify a specific set of actions that consistently cause the trouble to occur, the Technical Support Specialist and outline your steps to determine the problem.

Take the paper out of the paper tray and check to see that the top piece of paper is not crinkled or bent. You can also try this with the menu button on the monitor, which should bring up an options menu on the screen. See the basic troubleshooting section for a good starting point. Many operating systems, especially Windows, can conflict with new drivers.

If the printer is a LaserJet, try changing the toner cartridge. When used with reliable hardware with well-programmed drivers, a typical Windows computer shouldn't blue-screen at all. To make progress, we need another building block: simple, high-assurance hardware for secure computation."What does that actually mean? http://goinsource.com/is-this/is-this-a-serious-difficult-problem.html Chances are that if a problem begins after software starts, the software is causing it.

It makes no sound and there are no lights Check the Power Supply Check the Motherboard Check the CPU When I turn it on... Symptom The screen is shaking Diagnosis Move all objects that emit a magnetic field, such as a motor or transformer, away from the monitor. If you do not have a special protection, for your computer against electricity surges or sudden power failures, disruptions may occur causing massive data loss.Similarly, sudden and large changes in voltage How do I diagnose the problem?

You would also need a network connection to print to the network laser or color laser printers within CCRI. To correct this problem, you can turn off the feature. It is distinct from a software or firmware problem, which is normally caused by a defect in the software or operating system code respectively.A hardware problem is classified as a fault